HC150 Finger Bar Hedge Cutter
1.5 m Hydraulic Reciprocating Cutter Bar for Mini Excavators
The HC150 is a hydraulically powered finger bar hedge cutter attachment designed for mini excavators from 1.0 to 3.5 tonnes, delivering clean, precise cuts up to 40 mm thick with minimal disturbance to vegetation and wildlife. Its 1.5 m reciprocating cutter bar mounts via an adjustable bracket with 360° star-spline rotation, allowing horizontal, vertical and angled cutting around fences, poles and obstacles where flail cutters cannot reach.
Built for Maximum Accessibility
The HC150 mounts on the excavator’s rock breaker hydraulic lines and is supplied with hoses, couplings and adjustable mounting brackets, allowing fast installation across a wide range of carrier machines. The star-spline hitch permits 360° rotation in line with the excavator arm, so the bar can be set to any angle between horizontal and vertical. An optional one-metre extension bar and 360° swivel joint further extend reach to the far side of hedges.
Key Performance Specifications
-
Machine Carrier: 1.0–1.5 t (HC-150-5) / 2.0–3.5 t (HC-150-8)
-
Oil Flow Required: 20–30 L/min (HC-150-5) / 40–60 L/min (HC-150-8); optional low-flow motor available for 20–30 L/min
-
Cutting Width (Bar Length): 1,500 mm / 5 ft
-
Cutting Capacity: Up to 40 mm branch thickness
-
Operating Weight: 60 kg (without hitch)
-
Number of Teeth: 20 (individually replaceable)
-
Mounting: Adjustable bracket with Slanetrac star-spline 360° rotation
-
Drive: Hydraulic reciprocating finger bar, direct drive, no case drain required
-
Protection: Pressure relief valve protects motor from excessive load
-
Number of Blades/Cutters: 20 reciprocating cutting sections
Designed for Multiple Applications
The HC150 is ideally suited for:
-
Hedgerow trimming and shaping on residential and commercial sites
-
Roadside vegetation management for councils and contractors
-
Orchard and fruit tree pruning (citrus, apple, olive, mango, macadamia)
-
Fine hedge plants such as boxwood, ficus, murraya and juniper
-
Coarse hedges including privet, holly, hibiscus and lily pilly
-
Conifer and pine tree hedges
-
Nursery sapling and young plant trimming
-
Working around fences, walls, telephone poles and other obstacles
Its compact bar and end-mounted design allow operators to reach behind fences and close to obstacles where larger flail equipment cannot operate.
Powerful Cutting Performance
The HC150 uses sharpened reciprocating blades working alongside guiding steel fingers that direct branches into the cutting area, producing a clean cut rather than a torn finish.
Benefits include:
-
Clean, accurate cuts up to 40 mm, encouraging healthier regrowth than flail cutting
-
Heavy growth handled using the excavator’s slewing movement; lighter breasting using tracking movement for a fine finish
-
Individually replaceable cutting sections reduce maintenance cost and downtime
-
Pressure relief valve protects the hydraulic motor under load
-
Direct drive with no case drain required simplifies installation
-
Optional “Tiger Shark” coarse teeth available for thicker branches
The HC150 can be angled to suit the hedge face and operated from the excavator cab for continuous, controlled cutting.
Finger Bar Advantage
A key feature of the HC150 is its reciprocating finger bar configuration.
Benefits include:
-
Clean scissor-type cut rather than flail impact, reducing vegetation damage and wildlife disturbance
-
360° star-spline rotation allows cutting on unusual angles and hard-to-reach faces
-
End-mounted bar provides maximum reach around obstacles
-
Adjustable mounting brackets suit a wide range of excavator makes and models
-
Lightweight 60 kg bar reduces carrier load and transport requirements
-
Low-maintenance design with easily serviceable drive components
This configuration allows operators to trim hedges from the excavator cab without ladders, platforms or separate hedge-cutting machines.
Comfortable and Practical Operation
The HC150 is designed for straightforward installation and low routine maintenance.
Features include:
-
Supplied with hitch, hoses and couplings to suit the carrier machine
-
Connects directly to rock breaker lines for fast installation
-
Individually replaceable cutting sections for cost-effective servicing
-
Simple, robust steel construction with protected drive components
-
No case drain required, simplifying hydraulic setup
-
Optional one-metre extension bar and swivel joint for extended reach
-
Optional low-flow motor for carriers with 20–30 L/min hydraulic output
These features help ensure reliable performance across regular hedge-cutting work.
Why Choose the HC150 Finger Bar Hedge Cutter?
• 1.5 m / 5 ft cutting width
• Cuts branches up to 40 mm thick
• 20 individually replaceable cutting sections
• Hydraulic reciprocating finger bar with direct drive
• 360° star-spline rotation for angled cutting
• Adjustable mounting brackets suit 1.0–3.5 t excavators
• 60 kg operating weight without hitch
• Pressure relief valve protects hydraulic motor
• Optional extension bar, swivel joint, low-flow motor and coarse teeth
• Clean cut encourages healthy regrowth and minimises wildlife disturbance
Built to Trim Hedges from the Excavator Seat
The HC150 Finger Bar Hedge Cutter delivers precise, low-maintenance hedge-cutting performance as a mini excavator attachment. Designed for landscapers, farmers, councils and contractors working around fences, poles and restricted boundaries, it provides the reach, articulation and clean cutting action needed to maintain hedges and orchards efficiently without dedicated hedge-cutting machinery.
Contact us today for pricing, finance packages, available attachments, and delivery or collection options.














Reviews
There are no reviews yet.